Monday, September 16, 2013

A little bit more progress

So whats been happening then !
I booked 3 days leave from work to ferry the kids back to Uni with a weekend sandwiched in between, so 5 whole days. It transpires as 3 actually as 2 days were for above, one day it p***ed it down, the other day it rained p.m as I was in town in the a.m. So that left One day ! on which to get more progress.
I did though.
Firstly found LH winder mechanism in shed. The LH door glass was next together with mounting screws and winder handle.
Found front LH Indicator lens and frame in shed.
Found front bumper in loft and brackets in conservatory under a pile of wifeys artyfarty stuff.
Found LH quarter light assy in shed.

One thing that did puzzle me was...........I bought a pair of doors ( from you know where) about 4 years ago. Turned out they were crap, rusty, full of filler and poor lock chrome. However the quaterlights were good so I saved them down by the shed wrapped in polythene.
When it came time to find the LH door/window stuff I'm sure I had 3 RH side windows, quarterlights and winders !!
It took forever to figure out what was what and for which side.
Coo....the winder mechanism drove me nuts as I had four of them and trying to decide which way round they went was baffling.
Anyways, I cleaned up said winder mechanism with thinners,wire wool,soapy water and lithium based grease and fitted. Trouble is though the door is now heavier and its a swine to re-align and tighten the 6 door screws sufficiently so it does not drop.
Anyone got any Ideas better than the 6 Phillips screws used ?

Not thwarted I attached the quarterlights roughly. The top edge of the quarterlight seems a long way from the windscreen A pillar...eek.

N
Not quite shown in the picture due to the slight head on angle and I had a little jiggle around with the door.

I must admit that its good to be finally fitting stuff on rather than taking stuff off or even sanding.
I also have 4 window channel runners but think I've found out which way they fit..hopefully. Trouble is though I can't find the base bracket I fabricated a few years ago to hold it in position on the door bottom. I desperately need a selection of UNC/F nuts, bolts, screws/washers. MGB Hive do one for £18 ore so, so next payday will see me purchase one. I also need some to hold the front bumper to its brackets whilst I drill holes in the chassis rail.

That brings me to my next job.
Courtesy of the Canadian MGB register and Moss USA, I found the templates to weld up the indicator holes from the front ( Rubber) bumper position and new hole position to suit the chrome bumper light ( Yes I know its getting boring...another E-bay purchase, albeit 5 years ago).
So set to I did with 2 new in-fill pieces for LH & RH sides. Scrounged B & D jigsaw from Ma-in-law ( only wood blades available but hey ho it worked).

Picture to follow












Monday, September 02, 2013

Sanding and more sanding


After a mammoth wet/dry with 240 grit paper the A post is looking slightly better. All the old scratches from using 80 grit then 120 grit appear to have gone....or have they ?


The simple answer is NO !Shown is the remnants of the painted on "high build primer". Even after another sanding session and light guide coat of grey primer there are still many imperfections from the coarser grit paper used in isolated areas.
Time for more 240 "wet n drying" then. It then resembles much the same as the first picture except I'd spotted more areas along the top of the wing and near the front edge.

Fortunately after a days trolling round town Saturday morning with wifey I spotted more £1 cans of the grey primer. So on it went after a thorough clean and wipe. Look , it gleams !


Unfortunately there are STILL flaws in the paintwork !.
 a /. it was quite windy.
 b/. I'd not cleaned it as well as I though.
 c/. Did not rub it down enough !!!! FFS how much rubbing do you have to do.
Its funny though a few years ago this was the first wing to get a full coat of primer and after we/drying it looked fantastic. Must be the attention to detail I have now, since slight scratches from the original 120 grit paper are faintly visible, nay hit me in the eye..and sting.

Since the storm clouds were gathering and the wind getting up I called it a day.
I've decided to let the paint harden for a week, however I'm applying the acrylic stopper tomorrow hopefully it will harden sufficiently for more localised polishing/wet/drying. I'm getting a bit pissed of with the endless filling, rubbing, more rubbing, cleaning guide coating, repeat ad nausiem.

So as a diversion I'm going to modify the front wings to accept the chrome bumper style indicators and positioning. I may even fit the chrome bumper bracket ( bought from you know where) after some inventive  " modification" of the old rubber bumper mounting legs into captive nuts to fit inside the chassis rails. I have a rather explicit and diagrammatic instructions from the MG club of Toronto ( I think) which has lain sulking in the Lostsock secret repository for a few years ( As has the CB lights, bumper and irons).  I'm loathed to fit the irons with M8 thread and nuts but it looks as if I may have too.

Or I may just fit the door locks and mechanism instead. Oh the joys of MG restoration.